Error 0002 Xbox 360 Jasper
Melde dich an, um unangemessene Inhalte zu melden. I looked up on what the 2 red rings mean "overheating" so the Microsoft website said. I used 3 washers and a neoprene between the chassis. Tested mosfets as per a guide I found and related ones seemed normal. click site
After seeing it mentioned here I took a look, notice the damage and managed to pull one off a dead zephyr board. Wähle deine Sprache aus. Tried it and it wouldn't even boot, just an immediate 3RROD, still showing 0002 though. Any suggestions as to what I can do to fix this? https://xbox-experts.com/errorcode/E02/0002/
Error 0002 Xbox 360 Solucion
Is it likely that it is a MOSFET issue? Back to top #9 hobo1599 hobo1599 X-S Enthusiast Members 3 posts Posted 26 February 2010 - 07:28 PM QUOTE(Medeiros @ Feb 19 2010, 10:09 PM) I fixed my error 0002 by The output of these 'FETs then goes through a coil to clean it up, and it's then smoothed up more by some capacitors and such. So here is a few tips to help solve this problem.
- Symptoms of failure: -Xbox 360 turns on, and flashes 3 red lights IMMEDIATELY (not after a few seconds like on some other failures, such as the dreaded 0102).
- I have seen three cases of this happening so far.Symptoms of failure:-Xbox 360 turns on, and flashes 3 red lights IMMEDIATELY (not after a few seconds like on some other failures,
- if its compatible i had a feeling that the ethernet chip is the defective one because i originally had an e74 then 0002.
- So this means the component was good, as was the gpu reflow (0102) that I opened the system to do.
- I set everything up and turn it on only to see it doing the SAME THING..
- how can i check? (please be specific...
- So the mobo stays powered up, and frys itself.
- Does it mean I'm closer or is it a bad thing?
Details for Error code E02/0002 Cold solderjoint under CPU Add / Edit Details Primary Error code: 3 RLOD E-Code / Secondary Error code:E02 (No Audio/Video) / 0002 Binary/Hex:00000010 / 0x02 -> Any ideas? Lythius on 2011-06-20 19:15:26 : I have solved replace the C8U1 because it was open... Erro 0002 Xbox 360 Error Code 0002 After X-clamp Fix Started by XBOX 360 Onwer , Mar 26 2009 11:18 PM Page 1 of 2 1 2 Next Please log in to reply 18 replies
Most notably, 5V, 3.3V, and 1.8V. MaineUsedParts on 2012-05-25 07:01:31 : I just had a box that had bad USB sockets on the front. However, the "old" 5V point is straight off the MOSFETs, so current being drawn there does not go through the coil, so the motherboard cannot detect that current being drawn. can this be compatible?
Back to top #10 WorldFormula WorldFormula X-S Senior Member Members 196 posts Xbox Version:none 360 version:v4.0 (jasper) Posted 26 February 2010 - 10:54 PM Try removing everything off the board and Błąd 0002 Xbox 360 Do this row by row, column by column. how can i check? (please be specific... Rashid Mehmood thanx Stephen Lewis Could u give me info on the free samples Digg Twitter Facebook YouTube Email Recent [Fix] PG::CharacterNotInRepertoire: ERROR: invalid byte sequence for encoding "UTF8" How to
Error 0002 Xbox 360 Slim
Materials needed: * Soldering Iron * Mosfets (just get some free samples from onsemi.com) Procedure: 1) Open up the Xbox 360 and pull out the motherboard. 2) You will have to http://suhastech.com/fix-0001-0002-errors-on-your-xbox-360/ With a diverse range of content and a welcoming, amicable and tight-knit community, Se7enSins is a forum open to anyone and everyone. Error 0002 Xbox 360 Solucion This is a risky process as you risk frying the gpu and other chips. Xbox 360 Error 0002 Fix Veröffentlicht am 06.02.2013no fix or solutions yet now Kategorie Gaming Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen...
AplusConsoleRepair Dedicated MemberProgress to next rank:80% Posts: 18Joined: Tue Feb 26, 2013 12:51 amLocation: Cherry Hill, NJ Hasthanked: 2 times Beenthanked: 1 time Set up: aoyue 968 / Puhui 8280 get redirected here So you can use some cotton dipped in alcohol and clean the motherboard all through. The two circled in red are the ones that need to be replaced... Back to top #4 DeeMunz DeeMunz X-S Enthusiast Members 1 posts Location:Pennsylvania Xbox Version:unk 360 version:unknown Posted 01 October 2009 - 12:13 AM I have a Xbox 360 that is working Xbox 360 Error Code 0002
Check the specs in your owner's manual....I take no responsibility for someone breaking their multimeter by not listening. - Each mosfet will be soldered to the board by 3 seperate pins, Solutions:Clean your heatsinks and add a very very small amount of Arctic Cooling Paste between the GPU and the heatink and the GPU and the heatsink....THIS IS VERY IMPORTANT. You MUST have neoprene or nylon washers between the motherboard and the other metal washers used to space between the chassis. navigate to this website If it works, celebrate and play some Gears of War!!!
Can someone link me to a mosfet testing guide or point me in the right general direction please, thank you. Xbox 360 Jasper Failure Rate To replace these basic de-soldering skills are needed. I then loosened the screws little by little and kept powering the xbox on until i got an error free start...
However, to help fuel the fire, donations go a long way.
This bought me a few days until a hole wore through the tape (micro hole might I add). You will need a decent multimeter that has a diode test/continuity mode option with a rating of at least 3.3 volt over d.u.t. (diode under test). You will need a pretty good soldering iron to get it hot enough. Xbox 360 Jasper Power Supply Its still fixable with these errors.
You almost have to look parallel along the surface of the case to spot the small bumps. Hinzufügen Möchtest du dieses Video später noch einmal ansehen? luigirez1 on 2010-10-19 22:27:07 : Can also be caused by a transistor breaking off and being replace by a solder bridge. my review here You can also check your 360 with another working power brick. 1) If it doesn’t work – Your 360 is faulty. 2) If its does – Your Power brick is faulty
So the mobo stays powered up, and frys itself. there are a couple versions of the MOSFETs that I have come across..ON Semiconductor part # NTD60N02RGand some boards have this one.....International Rectifier part#IRLR3715ZIf replacing both of those still doesn't do but this is one of the few where im getting no where.