Home > Xbox 360 > Error 0002 Xbox 360 Fix

Error 0002 Xbox 360 Fix

Contents

max1zzz on 2013-04-21 00:31:28 : Had this on a xenon after a CPU swap (Downgrading dash to a jtagable version :) ) reflowed the CPU again and it worked fine Also Heres what i did. This will tell you the cut-off voltage, which is the highest voltage value that can be put on the gate without it passing a current. If your console is still covered by the 3 year warranty use it because Microsoft will fix it for free! More about the author

Solutions:Clean your heatsinks and add a very very small amount of Arctic Cooling Paste between the GPU and the heatink and the GPU and the heatsink....THIS IS VERY IMPORTANT. After seeing it mentioned here I took a look, notice the damage and managed to pull one off a dead zephyr board. You should get no signal, or an "open link" might be displayed on some digital multimeters. However, the "old" 5V point is straight off the MOSFETs, so current being drawn there does not go through the coil, so the motherboard cannot detect that current being drawn. https://xbox-experts.com/errorcode/E02/0002/

Xbox 360 Error Code 0002

Back to top #12 WorldFormula WorldFormula X-S Senior Member Members 196 posts Xbox Version:none 360 version:v4.0 (jasper) Posted 27 February 2010 - 08:31 AM heatsinks...yup. So the mobo stays powered up, and frys itself. Register now! Melde dich an, um unangemessene Inhalte zu melden.

I get home from work the third night and go to turn it on and the fans rev really high then flashes to 2 red rings. there could be a hell of alot of issues with this one. the heatsinks dont get hot. So, if the point shorts out due to ****** LED wiring or just some stupid mistake, it will draw excessive current, but the motherboard won't know it.

Top 2 reasons you will get a E02 or 0002 error after Xclamp mod.Symptoms: You perform the xclamp mod and when attempting to overheat your GPU you turn on the Xbox, replace MOSFETS So is this problem usually due to stupid mistakes? No I dont. You can find it online on eBay, some forum’s Trading Posts etc (XS, GI etc) If your Xbox 360 is faulty, here are some things you can try. 1) Sometimes, it

MikeLawry, Jan 2, 2011 MikeLawry, Jan 2, 2011 #4 Comrade Sit Nomine Digna Retired Messages: 12,430 Ratings: 6,180 Jan 2, 2011 #5 jmd almighty said: ↑ Tbh if you get one SB_12v.jpghttp://i50.photobucket.com/albums/f320/ ... I had the same exact problem the other day, 0031 before loosening the screws then 0002 afterward and i had to heat gun the mobo. Wird geladen...

  1. Wird geladen...
  2. Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch.
  3. a friend gave me his xbox.
  4. Suggestions?
  5. Therefore, by measuring the voltage drop across the coil, the motherboard knows how much current is being used, and it will shut itself off if too much current is being drawn
  6. This doesn't necessarily mean the PSU brick is broken, but that one or more of the components that regulate the voltage across the board to the various parts may be damaged.
  7. You must have enough washers below the motherboard (between the chassis and the motherboard) to prevent the motherboard from touching the chassis, if the motherboard touches the chassis it will ground

Erro 0002 Xbox 360

Somehow it was crushed when removing the xclamps.

working fine now! Xbox 360 Error Code 0002 Another way to get the replacements back on is to first lay down a dab of solder paste to each of the 3 pads to be soldered to, then preheat the Błąd 0002 Xbox 360 In the Falcon and newer boards, they actually upped the max voltage in the MOSFETs from 20v to 25v, so possibly this problem happens less often in the newer boards.in Falcon

All rights reserved. my review here Remaining characters: Anti-spam: Copyright Information: Lately it has come to our attention that more and more people stole content from this Error code Database without giving credit, some also restricted access knightmire on 2014-04-28 04:13:07 : I can confirm that the "C8U1" component caused this issue for me. hope this helps.QUOTE(SwisyNinja @ Feb 19 2010, 09:50 PM) im gettn 0002 wo any heatsinks but also w heatsinks. Xbox 360 Error Codes

Bitte versuche es später erneut. Hold the negative probe (-) to the center (drain) pin. but I can't figure out which one. click site has any one fix they xbox by replacing the MOSFETS?thank you Fri Mar 20, 2009 10:33 pm humboldt111502 Mr.

No account? The "C" it's around at the U8U1 on the bottom of the mainboard. is there a way to test the controller chip witha multimeter before remvoing it?

ON Semiconductor part # NCP5425.

airbuz320 on 2012-08-18 21:57:58 : I may or may not have solved my issue but thought I'd share the information to help others. Back to top #3 Driftek Driftek X-S Enthusiast Members 1 posts Posted 29 September 2009 - 03:32 PM I realize this is an old thread but I could not find the I was waiting for the correct washer to arrive so i just put a small piece of electrical tape between where the contact was made. Wird geladen...

Any suggestions as to what I can do to fix this? the mosfets i replace was 726 48 13NG from the original 801 48 13NHG. Edited by Driftek, 29 September 2009 - 03:32 PM. navigate to this website Users Online Content, Code and Design (CC)BY-NC-ND 2008-2016 Xbox-experts.com Contact/Terms of UsePrivacy PolicyCopyright InformationPrivacy PolicyFacebookTwitter Generated in 0.048 @ 127.0.0.1 NewsTutorialsShopForums FAQ • Search • Login Register View

Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. References: No References available! Some people bake the xbox but most get these professionally fixed..Great advice, and great first post lol.Did anyone learn how to fix this? Info about Mosfets.

Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen... Anmelden 3 10 Dieses Video gefällt dir nicht? always making sure that the neoprene washers are the only washers touching the motherboard. Top 2 reasons you will get a E02 or 0002 error after Xclamp mod.Symptoms: You perform the xclamp mod and when attempting to overheat your GPU you turn on the Xbox,