Home > Error Code > Email Error Code 501

Email Error Code 501

Contents

This status code is received when the server does not support the facility required. Klensin IESG X.7.15 Priority Level is too low 450, 550 (other 4XX or 5XX codes are allowed) The specified priority level is below the lowest priority acceptable for the receiving SMTP Vaudreuil IESG X.1.YYY Addressing Status The address status reports on the originator or destination address. This is a special case of X.7.21. (This violates the advice of Section 6.1 of [RFC6376].) [RFC7372] (Standards Track); [RFC6376] (Standards Track) M. navigate here

Kucherawy IESG X.7.19 RRVS test cannot be completed 5XX This status code is returned when a message is received with a Require-Recipient-Valid-Since field or RRVS extension and the receiving system cannot I manage a number of on-line sites through 1and1, my personal domain is via 1and1 also. Vaudreuil IESG X.1.2 Bad destination system address Not given The destination system specified in the address does not exist or is incapable of accepting mail. Siemborski, A. http://www.serversmtp.com/en/smtp-error

Error Code 501 Android

For other information check out our article on what is an SMTP server.252The server cannot verify the user, but it will try to deliver the message anyway.The recipient's email account is Klensin IESG X.2.0 Other or undefined mailbox status Not given The mailbox exists, but something about the destination mailbox has caused the sending of this DSN. [RFC3463] (Standards Track) G. Tweet Question Actions Stream Use this widget to see the actions stream for the question. Probably the mailing after your next one depending on the frequency of your mailings may be a good idea (for example, if you e-mail once per month, it's probably safe to

Vaudreuil IESG X.1.8 Bad sender's system address 451, 501 The sender's system specified in the address does not exist or is incapable of accepting return mail. Detail sub-codes may provide notification of transformations required for delivery. [RFC3463] (Standards track) G. I'm bookmarking it now… - KJ carmelo Sicurello Sep 27, 2012, 2:15 Reply Someone trying to send to us is getting the following bounce returned to them… There was a Error Code 511 This may be a permanent error if the mailbox will never be re-enabled or a transient error if the mailbox is only temporarily disabled. [RFC3463] (Standards Track) G.

Vaudreuil IESG X.4.6 Routing loop detected Not given A routing loop caused the message to be forwarded too many times, either because of incorrect routing tables or a user- forwarding loop. Suggest to wait for a few days and deliver your email again or if it is someone you know, just call up on a phone. blessedtag Aug 23, 2012, 13:40 For domain names, this means the address portion to the right of the "@" is invalid for mail. [RFC3463] (Standards Track) G. http://www.greenend.org.uk/rjk/tech/smtpreplies.html This memo does not discuss the merits of any such filtering, but provides a mechanism to report such.

Vaudreuil IESG X.5.0 Other or undefined protocol status 220, 250, 251, 252, 253, 451, 452, 454, 458, 459, 501, 502, 503, 554 Something was wrong with the protocol necessary to deliver Error Code 504 turboSMTP, for instance, comes with a 24/7 customer support: you can try it free and forget once for all these issues.And here's a list of the main SMTP error or reply I am using a web hosting with unlimited storage. Melnikov IESG X.6.0 Other or undefined media error Not given Something about the content of a message caused it to be considered undeliverable and the problem cannot be well expressed with

Ariston Boiler Error Code 501

Meaning, if both your address and the recipient's are not locally hosted by the server, a relay can be interrupted.It's a (not very clever) strategy to prevent spamming. have a peek at this web-site This is useful only as a persistent transient error. [RFC3463] (Standards Track) G. Error Code 501 Android Hansen, J. Error Code 510 Melnikov IESG X.4.0 Other or undefined network or routing status Not given Something went wrong with the networking, but it is not clear what the problem is, or the problem cannot

If this code accompanies a delivery failure report, sending in the future may be successful. [RFC3463] (Standards track) G. check over here Klensin IESG X.3.3 System not capable of selected features Not given Selected features specified for the message are not supported by the destination system. Check the RFC index for further mail-related RFCs. Vaudreuil, J. Error Code 502

Vaudreuil IESG X.3.6 Requested priority was changed 250 or 251 The message was accepted for relay/delivery, but the requested priority (possibly the implied default) was not honoured. It's the typical response to the DATA command.The server has received the "From" and "To" details of the email, and is ready to get the body message.420"Timeout connection problem": there have the email address was active few hours ago (and for the last 8 years), and then all my email to the recipient was returned with the the 550 error… how do his comment is here This condition might be temporary, for example the server is operating in a mode where only higher priority messages below certain size are accepted for transfer and delivery. [RFC6710] (Standards Track)

Vaudreuil IESG X.1.7 Bad sender's mailbox address syntax Not given The sender's address was syntactically invalid. Error Code 401 For more information about how to get your email to the inbox with SuretyMail, see SuretyMail.com. Vaudreuil IESG X.4.5 Mail system congestion 451 The mail system was unable to deliver the message because the mail system was congested.

Not what you were looking for?

There should be an error or a misspelling somewhere.554This means that the transaction has failed. Vaudreuil IESG X.1.5 Destination address valid 250 This mailbox address as specified was valid. There could be a lot of reasons, including that someone entered it wrong, or that someone intentionally entered a fake email address into your system (such as when you require a Error Code 404 Vaudreuil IESG X.2.YYY Mailbox Status Mailbox status indicates that something having to do with the mailbox has caused this DSN.

Vaudreuil IESG X.6.YYY Message Content or Media Status The message content or media status codes report failures involving the content of the message. And, even if they are going to come back some day and clear out their inbox, do you think that they are really going to stop to read your email? Have just received this message: "There was a SMTP communication problem with the recipient's email server. weblink Different ISP's respond differently in this regard, so if after a few tries (say 2-3 tries) you're still not getting mail delivered, it's probably safe to temporarily remove the subscriber from

This is useful only as a permanent error. [RFC3463] (Standards Track) G. This status code should be used when the per-mailbox message length limit is less than the general system limit. You should try again sending smaller sets of emails instead of one big mail-out.432Typical side-message: "The recipient's Exchange Server incoming mail queue has been stopped".It's a Microsoft Exchange Server's SMTP error